News

Computer stripping machine stripping is not open thread 1. Check the depth of cut line, adjust the value of smaller diameter. 2. Line transmission wheel gap is too large, adjust the gap into line transmission wheel. 3. Set stripping head is larger than 2mm. 4. Line possession of stolen goods. 5. Retract set too, need to be reduced. Wire stripping machine stripping tail does not open 1. Check the depth of cut line, adjust the value of smaller diameter. 2. round qualifying transmission gap is too large, adjust the gap is small qualifying transmission wheel. 3. Set stripping head is larger than 2mm. The retraction is set too small need adjusting. Sheath bruised 1. Adjust the gap into the transmission wheel and outgoing transmission line between rounds. 2. The contact with the factory, replace the transmission wheel. Wire core is cut bad 1. Bring a large diameter value until the appropriate level (blade just cut the skin but not hurt stringing wire core for the best position). 2. If the line is very thin skin, after peeling can not be transferred to the diameter found, it may be appropriate to reduce the retraction value. Of varying lengths, there grew up in the actual line or equal to the set line length 1. Line transmission wheel gap is too big, and sometimes not peel open thread, thread stripping line not open more than a set length, adjust the "Line lash adjuster wheel", increasing the pressure. 2. Line pipe, there are stolen goods, check and properly cleaned. 3. Adjust the pressure line transmission wheel. Of varying lengths, appear actual line length less than or equal to the set line length 1. The wire itself varying thickness. 2. Scroll wheels have stolen goods, the need to clean up. Wire surface wax, resulting in the inlet and outlet transfer wheel slip. 3. Remove the line, the program is set to "00", the dry run, stop and check "into, qualifying round of the" rotation is flexible or catching phenomenon. 4. line planes have catching phenomenon, leading to the input line slipping phenomenon. Long core section 1. The diameter is too small, knife cut to the core, when stripping out, the need to increase the diameter value of 1-2. 2. Retract set too small, it should be appropriate to increase the retraction parameters. Sometimes there is no cut wires together 1. Place the blade moving parts add oil, try (usually refuel once every 8 hours of operation). 2. will slow the pace, and try again. 3. Check the wire specifications, please allow this type of models within the range. 4. Does the blades become dull. Incision inclined tangent 1. Bend the wire itself too, need to straighten. 2. Wire port is not being on the edge center

1.Multifunction high-speed computer stripping machine is a high speed line material factory size cut ends of stripping, stripping a single-ended and semi-automatic wire cutting stripping machine. 2. Use servo motor control wire cutting, stripping and other movements more precise cutting length. 3. The length of the conversion and the whole stripping, semi-stripping mode setting using the buttons, simple and fast. 4. Stripping length charge and transform rotary cutter depth using the trimming mode, simple and fast. 5. The speed can be divided into five sections, the wire can be based on the specifications set so thick, thin can stabilize production. 6. Each inspection standard atmospheric pressure is low, the cylinder locking motor abnormalities consistent counting and other functions, can automatically shut down abnormal and detection Show on man-machine interface, convenient and rapid troubleshooting to minimize downtime. 7. The best characterized as a technical adjustment, less pressure line, adjust the time is short, simple and easy to operate. 8. Can be used with sub-line machine, complete sub-line cable, the cut line and stripping operation, improve production efficiency. 9. The machining 600mm long can pull 50 times per minute, more than four times the 2 desktop a stripping machine.

Computer stripping machine works; microcomputer technology to deliver the wire by controlling the line round, qualifying round, and by controlling the turret assembly to complete the tangent and stripping. And each member Main Features: 1.Qualifying round: transportation stripping wire and outlet end; 2.Into the line wheel lash adjuster wheel: Adjust the line wheel gap, the gap is reduced to a small rotating, to a large gap increases; 3.The catheter assembly: wire from the feed line to the turret wheel assembly, ensure wire catheter straight, easy road to prevent the wire 4.The line wheel: transportation stripping wire and outlet headers; 5.Turret assembly: wire cutting, stripping stripping head and tail; 6.Qualifying round lash adjuster wheel: adjust qualifying round gap, to a large rotating gap increases, reduced to a small gap.

diameter 10-65mm wire stripping,two rollers,two blades,fast and effective.

Separating Iron,Copper,Aluminium from scrap Radiator

New Type Wire Stripping Machine Ready for shipping

To recommend the best copper wire stripper machine for your needs, please provide the following details: 1. Wire Specifications: Diameter Range: (e.g., 0.5mm–10mm, thick cables, etc.) Insulation Type: (PVC, rubber, shielded cables, etc.) Quantity: Small batches or bulk processing (e.g., 50kg/day vs. 1 ton/day). 2. Preferred Machine Type: Manual Stripper (low cost, small-scale). Automatic Stripper (fast, for medium/large volumes). Granulator/Shredder (for mixed or complex cables). 3. Budget Range: Economy ($100–$1,000). Industrial ($1,000–$20,000). 4. Additional Needs: Portability (benchtop vs. floor-standing). Safety features (dust collection, noise reduction). Example Recommendations Based on Common Scenarios: A. Small Workshop (Thin Wires, Low Volume): Manual Option: Klein Tools Katapult Wire Stripper (adjustable, handles 10–20 AWG). Automatic Option: Tecnofer EKO 2.0 (up to 25mm, ~50kg/hour). B. Recycling Business (Mixed Cables, High Volume): Granulator: Copper Rec QR-800 (processes 200–500kg/hour, separates copper/plastic). Heavy-Duty Stripper: Kaideng KD-300 (for 1–30mm wires, fully automatic). C. Industrial Scrap Processing: Shredder System: Eldan Recycling Plant (for tons/day, integrates crushing/sorting).

A  Copper Wire Stripper Machine is a specialized device designed to remove insulation from copper wires efficiently, enabling the recovery of valuable copper for recycling or reuse. Here’s a concise overview:   Types of Copper Wire Strippers: 1. Manual Strippers:      - Hand-operated tools for small-scale work (e.g., electricians).      - Examples: Adjustable blade strippers, plier-type strippers.     2. Automatic Stripping Machines:      - Motorized machines for bulk processing.      - Features:        - Adjustable blades for different wire diameters.        - High-speed operation (e.g., 50–200 kg/hour).        - Options for single-sided or full stripping.     3. Industrial Granulators/Shredders:      - Crush wires and separate copper from insulation via vibration/airflow.      - Suitable for mixed or thick cables.     Key Features to Consider: - Wire Diameter Range: Machines vary (e.g., 0.1–45 mm).   - Blade Material: Tungsten carbide blades last longer.   - Efficiency: Automatic models save labor time.   - Safety: Look for overload protection and emergency stops.     Applications: - Recycling centers, scrap metal processing, and electrical workshops.     Popular Brands: - Copper Rec** (granulators), Tecnofer(strippers), Kaideng** (small-scale machines).  Mrecycling.   Cost: - Manual tools: $20–$100.   - Automatic machines: $1,000–$20,000 (capacity-dependent).     For bulk processing, automatic strippers or granulators are ideal. For precision, manual tools suffice. Always prioritize safety certifications (e.g., CE, UL).     Would you like recommendations based on your specific needs (e.g., wire type, volume)?

copper wire stripper

Wire Stripping machine is used for copper wire separating